Azle, TX · Tarrant & Parker counties
24/7 HVAC Services in Azle, TX: Air Conditioning and Heating
AC blowing warm, furnace out, heat pump iced over: one call reaches a person any hour, and a licensed HVAC contractor comes out with the price before the work.
- 24/7 live answer
- Licensed and insured HVAC contractors
- Price before work starts
By the Geaux 72 Air & Heat team · Updated
Heating and air for Azle, without the guesswork
When the AC quits on a 102-degree afternoon, the thermostat tells you almost nothing. A dead capacitor, a tripped float switch on a clogged condensate line, a refrigerant leak and a worn-out compressor can all look the same from the hallway: the fan runs and the house keeps getting hotter.
Guessing is how a small repair turns into a big bill. Running a frozen coil, resetting a breaker over and over or topping off refrigerant without finding the leak each make the next visit more expensive.
Geaux 72 Air & Heat answers (321) 478-0693 24 hours a day and sends a licensed, insured Texas HVAC contractor to homes in Azle and the towns around it. The technician diagnoses first, explains what failed and gives you the price before any repair. Air conditioning, gas and propane furnaces, heat pumps, mini-splits and the ductwork that connects it all.
AC or heat out right now?
Four safe checks, then call
- 1Thermostat: set to Cool (or Heat), a few degrees past room temperature, fresh batteries if the screen is blank.
- 2Breakers: look for a tripped AC, air handler or furnace breaker. Reset it once. If it trips again, leave it off.
- 3Filter: a clogged filter can freeze the coil in summer and trip the furnace limit switch in winter.
- 4Ice, water or a burning smell: turn the system off and call (321) 478-0693. We answer 24/7.
Smell gas or hear a CO alarm? Leave the house first. From outside, call Atmos Energy or your propane supplier and 911. Do not flip switches or try to find the leak.
Call (321) 478-0693Full checklist: 7 checks to make when the AC stops working.
What we handle
HVAC services for Azle homes
Cooling, heating and the ducts in between. Each page explains how the work is done in a North Texas house, what it involves and what to ask before anyone starts.
AC Repair
Warm air from the vents, a condenser that hums but will not start, ice on the copper lines or water dripping from the attic. The technician we send finds the failed part, gives you a written price before any repair, then tests the system under load. Capacitors, contactors, fan motors, leaks and drains.
Learn moreAC Installation and Replacement
An old R-22 unit, a third big repair in two summers or a house that never cooled right. The contractor we send sizes the new system with a load calculation, matches the condenser, coil and furnace or air handler, pulls the permit and tests the start-up. You get a written quote first.
Learn moreFurnace and Heating Repair
No heat, cold air from the vents or a furnace that lights and quits. Gas furnaces on Atmos lines, propane furnaces on rural properties and electric heat strips in all-electric homes each fail differently. The technician we send finds the fault, checks for carbon monoxide risks and prices the repair before work.
Learn moreHeat Pump Repair and Installation
Heat pump blowing cool air, icing over or running nonstop? We dispatch licensed HVAC contractors to diagnose defrost boards, reversing valves, heat strips and refrigerant problems, and to replace worn heat pumps with properly sized SEER2 systems. Ductless mini-splits for shops, garages and lake cabins too. All-electric, propane and dual-fuel homes around Azle.
Learn moreAir Duct Repair and Replacement
Hot back bedrooms, weak airflow or a dusty house often trace to the ducts, not the AC. We dispatch licensed HVAC contractors to test duct leakage and static pressure, repair sagging or crushed attic flex duct, add return air, fix manufactured-home crossovers and replace worn duct systems around Azle.
Learn more24/7 Emergency AC and Heating Repair
AC dead on a 100-degree afternoon or no heat in a hard freeze? Call any hour and a live person answers, walks you through safe checks and dispatches the nearest available licensed HVAC contractor. We confirm timing on the call and you get the price, including any after-hours charge, before work starts.
Learn moreNot sure which one you need?
Tell us what the system is doing and we'll send the right technician. Tune-ups, thermostats and mini-splits are handled under the services above.
Local knowledge
HVAC problems we see in Azle homes
Azle grew from about 2,700 people in 1960 to roughly 13,400 at the 2020 Census, and the median home here was built around 1987. In practice that means a lot of brick ranch houses on their second or third air conditioner, with the air handler in the attic or a hall closet and flex duct that may be as old as the house.
Add a cooling season that runs from April into October, about 20 days at or above 100 degrees in a normal DFW summer, spring hail, and a town that straddles Tarrant and Parker counties with gas service in some streets and propane on others. About one resident in seven moved in during the past year, so plenty of owners are living with a system they know nothing about. The technician who knows these patterns checks the right parts first.
100-degree afternoons and failed capacitors
A run capacitor is a small part that gets a big job in July: starting the compressor and condenser fan dozens of times a day in 100-degree heat. It is the single most common reason an Azle AC hums but will not start, and usually one of the simpler repairs.
More on AC repair in AzleAttic air handlers and old flex duct
Most Azle homes went up between the 1960s and the 1990s, and many put the air handler and the ductwork in an attic that tops 130 degrees in summer. Sagging, torn or disconnected flex duct can lose a big share of the cooling before it reaches a room.
More on air duct repairAging R-22 and R-410A systems
Some original and second-generation systems still run on R-22, which has not been made in the U.S. since 2020. Newer R-410A equipment can still be serviced, but every new system installed today uses R-454B or R-32. That changes the repair-or-replace math.
More on AC installation and replacementPropane and all-electric homes past the gas mains
Atmos Energy serves natural gas in town. Out toward Reno, Pelican Bay, Springtown and the acreage roads, homes heat with propane furnaces, heat pumps or electric heat strips, each with its own failure points and its own winter questions.
More on heat pump repairNo-heat calls in a hard freeze
North Texas winters are mild until they are not. When a front drops the temperature into the teens, as it did in February 2021, igniters, flame sensors, heat pump defrost controls and frozen condensate drains all fail at once, and calls arrive in a rush.
More on furnace and heating repairMuggy rooms on humid summer nights
Gulf moisture rides north into DFW, so a house can hit the thermostat setting and still feel clammy. An oversized system that short-cycles, a dirty coil, a slow condensate drain or leaky attic ducts pulling in hot attic air all leave humidity behind. The fix starts with runtime, airflow and coil readings, not a bigger unit.
More on why an AC runs but does not cool
Symptoms, safe first moves and what the technician checks
Use this to describe the problem on the phone, not as a diagnosis. Refrigerant, wiring and gas parts are for a licensed technician; your part is to observe and stay safe.
| What you notice | Your safe first move | What the technician checks |
|---|---|---|
| AC runs, air from the vents is warm | Thermostat on Cool and below room temp; filter; is the outdoor fan spinning? | Capacitor, contactor, condenser fan motor, refrigerant level, coil condition |
| Ice on the copper line or indoor coil | Switch the thermostat to Fan only (or Off) and let it thaw; do not chip ice | Airflow, blower, dirty coil, low refrigerant from a leak |
| Water at the attic air handler or a ceiling stain | Turn the system off; check whether the float switch has tripped | Clogged condensate line, cracked or rusted drain pan, failed float switch |
| Breaker trips when the AC starts | Reset it once. If it trips again, leave it off | Shorted compressor or fan motor, failing capacitor, wiring at the disconnect |
| Furnace runs but blows cold air | Check the filter and that the thermostat says Heat; reset furnace power once | Igniter, flame sensor, gas or propane supply, inducer motor, limit switch |
| Condenser quit after hail, lightning or an outage | Turn the system off at the thermostat; if safe, switch off the outdoor disconnect. Photograph the unit before cleanup | Contactor, capacitor, control board and fuses at the disconnect; fin and coil damage; compressor start |
| House reaches the setting but feels clammy or musty | Note how long the system runs and whether it short-cycles; check the filter | Equipment sizing and runtime, coil condition, condensate drainage, duct leakage pulling in attic air |
| Gas smell or CO alarm | Leave the house now. Call Atmos Energy or your propane supplier and 911 from outside | Nothing until the gas utility or fire department clears the house |
After a North Texas storm
Hail, wind or a power surge: what to photograph before the technician arrives
Spring storms across Parker and Tarrant counties bring hail that flattens condenser fins, wind that drops limbs on outdoor units, and lightning or outages that leave a system unable to start. When a condenser quits after a storm near Eagle Mountain Lake, the useful first moves are photos and a safe shutdown, then a technician checking the disconnect, capacitor, contactor and controls instead of guessing from the thermostat.
Take these photos first, if it is safe
- The outdoor condenser from several angles, wide and close (dents, bent fins, a crushed top grille)
- The thermostat display, mode and any error code
- The electrical panel and breaker positions, from a safe distance, without opening anything
- The model and serial plate on the outdoor unit
- Fallen branches, standing water or damage around the unit
- The date and rough time of the hail, wind, lightning or outage
- Recent invoices and maintenance records
If a breaker keeps tripping, stop resetting it. After a suspected surge, turn the system off at the thermostat and, if you can do it safely, pull the outdoor disconnect. Do not open panels or touch wiring.
How the contractor supports an insurance claim
- 1Make the area safe and photograph it before anything is moved or cleaned up.
- 2Call and describe the storm or surge timeline; the technician checks the disconnect, electrical parts and coil.
- 3Get written findings with photos, the repair options and the price for each.
- 4Share the report with your insurer or adjuster and ask what else they need.
- 5Confirm approval, your deductible, any permit and payment timing before work begins.
- 6Keep the final invoice, warranty paperwork and completion photos.
The contractor documents what it observed: equipment condition, test results, the repair scope and the price. Your insurer and your policy decide coverage. A good report keeps storm damage separate from age and wear, and nobody should promise you that a repair or a new system will be covered. For a unit that will not start right now, see 24/7 emergency AC and heating repair.
How it works
Call, dispatch, price, job done
You call, any hour
A person answers, asks what the system is doing and walks you through the safe checks while you are on the phone.
We dispatch
The nearest available licensed HVAC contractor is sent to your address. You hear the expected timing on the call, not a promise we cannot keep.
Diagnosis and price
The technician tests the system, shows you what failed and gives you the price before any repair starts.
Fixed and tested
The approved repair is made, then the system is run and checked: temperature split, amp draw, drainage and safety controls.
What the technician checks during the diagnosis
A symptom is not a diagnosis. The exact tests depend on the equipment, but a proper Azle service call works through the system in order before anyone quotes a part:
- The symptom you reported, the system age, any recent storm or outage, and past repairs
- The thermostat call: is it actually asking for cooling or heat?
- Power at the breaker, the outdoor disconnect and the air handler or furnace
- Airflow and the temperature split across the indoor coil
- The condensate path: drain line, pan and float switch
- Electrical parts tied to the symptom (capacitor, contactor, motors, control board) and refrigerant readings where they apply
You should hear what failed in plain English, see the reading or the part when it helps, and get the price before approving anything. Ask up front whether a diagnostic or after-hours charge applies, and whether it is credited toward the repair you approve.
Straight answers
Repair, replace, and who is doing the work
When a repair makes sense
- The failure is one identified part and the rest of the system tests well
- The system uses R-410A and has no leak history
- The house cooled evenly until this week
- The repair is small next to the value of a system with years left
When replacement deserves a look
- An R-22 system with a refrigerant leak
- A failed compressor or evaporator coil on a system past 12 to 15 years
- Repeat repairs, rooms that never cool, or bills that keep climbing
- Sizing that was a guess: a new system should start with a Manual J load calculation
Credentials you can check
In Texas, air conditioning and heating contractors are licensed by TDLR, and the technicians who come to your house work under that license. Refrigerant work also requires EPA Section 608 certification.
The license class tells you the scope: Class A covers systems of any size, and Class B covers cooling systems up to 25 tons and heating up to 1.5 million Btu per hour, which covers any home in town. Ask for proof of liability insurance in writing, and workers' compensation information where it applies.
Every HVAC contractor we send is licensed and insured in Texas. Ask the technician for the contractor's license and look it up on the TDLR License Search before you sign anything.
What a replacement estimate should list
- A Manual J load calculation for your house, not the size of the old unit
- How Manual S guided the equipment choice, and whether Manual D duct changes are needed for hot or cold rooms
- Equipment, labor, removal and refrigerant recovery as separate lines
- Start-up testing, the permit and any accessories or duct work
- Manufacturer and workmanship warranty terms, and the payment milestones
When nothing is unsafe, it is reasonable to compare written quotes line by line. More on AC installation and replacement.
Permits depend on the address
Azle straddles Parker and Tarrant counties, and an Azle mailing address does not always mean the house is inside city limits. Inside the City of Azle, replacing equipment and other covered mechanical work generally needs a permit and an inspection. Homes outside city limits follow county rules instead.
The licensed contractor confirms the jurisdiction, pulls any permit and schedules the inspection. Ask who is responsible for the permit and its fee, and ask for the permit number when one is required. A repair visit usually does not need one.
Warranties and financing: get it in writing
Two different promises come with a new system. The manufacturer warranty covers eligible equipment parts under its terms, often only if the unit is registered. The workmanship warranty comes from the contractor and covers the installation or repair itself. Ask for both in writing, with their length, exclusions and who to call first.
If a contractor offers financing, approval comes from the lender, not the contractor. Before signing, confirm the lender, the term and rate, what happens after any promotional period, and whether a deposit is due. Keep the invoice, model and serial numbers and start-up report together.
Why call us
Why Azle homeowners call Geaux 72
A live answer at 2 a.m.
AC failures do not wait for office hours, and neither do frozen January nights. A person picks up 24/7 and starts dispatch on the call.
Licensed and insured contractors
Every HVAC contractor we send is licensed and insured in Texas. You can verify the contractor's license with TDLR before anything is signed.
Price before work
The technician explains the problem in plain English and gives you the price first. You approve the repair or you do not.
Built around Azle houses
1980s ranch homes with attic air handlers, lake houses on Eagle Mountain Lake, manufactured homes on acreage: each fails in its own way.
Repair first, replace when it makes sense
A capacitor is not a reason to sell you a new system. When replacement is the better call, you get the reasons in writing.
Straight about timing
In a heat wave every contractor in North Texas is booked. We tell you the honest wait instead of a number that sounds good.
About Geaux 72
One local number for heating and air
Geaux 72 Air & Heat is an Azle-based answering and dispatch line for heating and air conditioning. Geaux 72 Air & Heat connects you with independent licensed HVAC contractors who perform the work. Our job is to get the right technician to your door and make sure you understand what they find before you pay for anything.
We are honest about what we are: no invented review counts, no borrowed certifications, no arrival time we cannot keep. A phone that gets answered, a contractor who diagnoses before quoting, and a price you hear first.
Areas we serve
Azle and the towns around it
Up SH 199 to Springtown, down it to Lake Worth, and across I-820 to Saginaw and White Settlement. See every HVAC service area.
Around Eagle Mountain Lake and the SH 199 corridor
Closer in, we cover the small communities that share Azle's roads and its weather: Reno, Pelican Bay, Sanctuary, Lakeside and Briar. That means lake houses and cabins with closet air handlers along Eagle Mountain Lake, manufactured homes and shops on acreage toward Reno and Springtown, and the light commercial buildings along Jacksboro Highway. The same summer heat and the same winter fronts hit all of them. Homes in Eagle Mountain and along Boat Club Road on the east shore, and on the northwest edge of Fort Worth near Lake Worth and Saginaw, often have Fort Worth mailing addresses; call to confirm your address before scheduling.
What to expect on dispatch
- We confirm your address before talking about arrival.
- You hear the expected timing on the call; a town on a list is not a response time.
- During a heat wave or a hard freeze, every contractor is stretched, and we say so.
- Not sure you are in range? Call and we will tell you honestly.
Maintenance
A North Texas HVAC calendar that prevents the 3 a.m. call
March and April
Cooling tune-up before the first 95-degree week: capacitor and contactor check, coil cleaning, refrigerant readings, condensate line flush.
May and June
Cottonwood fluff and mowing clippings coat outdoor coils. Rinse the condenser gently with the power off, and keep two feet clear around it.
After spring hail
Look at the condenser fins and the top grille. Bent fins and a dented coil cut airflow; photograph the damage before anything is cleaned up.
October and November
Heating check before the first cold front: igniter, flame sensor, heat exchanger inspection, heat strips and the heat pump defrost cycle.
Step-by-step: the spring AC tune-up checklist for North Texas homes and what to check when there is no heat in a Texas freeze.
Placeholder · reviews coming soon
What Azle homeowners say
This line is new to Azle, and we won't publish a star rating or a testimonial we can't back up. As homeowners in Azle, Springtown, Lake Worth and the lake communities around Eagle Mountain Lake share how their calls went, their verified reviews will appear here with a link to the source.
Until then: Every HVAC contractor we send is licensed and insured in Texas. You hear the price before any work starts.
HVAC questions from Azle homeowners
Are you really answering 24 hours a day in Azle?
Are the contractors you send licensed and insured?
Will I know the price before work starts?
My AC is running but the house will not cool. What should I check first?
Is it worth repairing an older system that uses R-22?
Do you work on propane furnaces and heat pumps outside town?
How long does an AC system last in North Texas?
Do you need a street address to send someone?
What HVAC services does a contractor in Azle, TX provide?
How much does HVAC repair cost in Azle, TX?
How do HVAC technicians diagnose an air conditioning problem?
How can I tell whether my HVAC system needs repair or replacement?
Why should a replacement HVAC system receive a Manual J load calculation?
Why does North Texas humidity make an HVAC system work harder?
When should I call for same-day or emergency HVAC service in Azle?
What should I photograph before an HVAC technician arrives after storm damage?
Does HVAC work in Azle require a city permit?
Which warranty details should I compare before replacing an HVAC system?
When is the best time of year to schedule HVAC maintenance?
Maintained by the Geaux 72 Air & Heat team · last reviewed October 2026. Every HVAC contractor we send is licensed and insured in Texas. Geaux 72 Air & Heat connects you with independent licensed HVAC contractors who perform the work.
Guides
Before you call, or while you wait
Heating
Heat Pump or Furnace for a Home Near Azle? Natural Gas, Propane and All-Electric Compared
How natural gas, propane, heat strips, heat pumps and dual fuel compare for homes in and around Azle, and how each one holds up in a hard freeze.
Maintenance
Spring AC Tune-Up Checklist for North Texas Homes
The cheapest AC repair is the one found in March. Here is the spring checklist: what you can safely handle at home and what a technician should test before the first 95-degree week.
AC Troubleshooting
AC Running but Not Cooling: 8 Causes in a Texas Summer
Eight reasons an AC keeps running without cooling the house on a 100-degree day, and the simple vent measurement that tells you where to look first.
Get help now
Call Azle's 24/7 heating and air line
For anything urgent (no cooling in July, no heat on a freezing night, water coming through a ceiling under the air handler), calling is faster than a form. A person answers at (321) 478-0693.
Have this ready when you call
- 1The service address and the best number to reach you
- 2What the system is doing: no cooling, no heat, ice, water, noise or a tripped breaker
- 3Gas, propane or all-electric heat, if you know
- 4The age of the system or the model plate on the outdoor unit, if it is easy to see
Not urgent? Send a request
For the fastest help, call (321) 478-0693. Or send a few details and we'll reach out.